Electrostatic Products
Trek 323
Highly Sensitive, Versatile Electrostatic Voltmeter, Measure 0 to ±100 V
Advanced Energy's Trek 323 electrostatic voltmeter is ideal for highly sensitive voltage measurements and can be used with various side-view probes.
- Measurement Range: 0 to ±100 V DC or peak AC
- Accuracy: Better than 0.05% of full-scale
- Speed of Response (10 to 90%): Less than 300 ms for a 100 V step (adjustable)
- Overview
- Technical Specs
- Documents
- Accessories
- Service & Support
- Distributors
Overview
The Trek® 323 is a versatile instrument. Use in various electrostatic applications, including materials evaluation, electret studies, charge accumulation on disk drive assemblies, and other extremely sensitive ESD sensitive components.
The Trek 323 features adjustments to compensate for many sensitive testing conditions. Response speed control adjusts the speed/noise tradeoff of the AC response. And the drift/spacing null adjustment minimizes the variation in zero-offset voltages as the probe-to-test surface spacing changes.
Benefits
- Utilize low impedance probe sensor that assures high accuracy in high humidity and contaminated environments (e.g. airborne dust, toner, ions, and chemicals)
- Monitor detected output voltage through a 1:1 voltage monitor output and a switch-selectable scale of 10:1 or 20:1 voltage monitor output
- Use with various shaped probes (e.g. round, square)
Features
- Sensitivity: 5 mV
- Drift spacing/null adjustment
- Response speed control
- Additional probes available
Select specifications are shown below. Please see product data sheet for additional specifications.
-
Performance
Measurement Range
0 to ±100 V DC or peak AC
DC Accuracy
Better than 0.05% of full-scale
Speed of Response (10 to 90%)
Less than 300 ms for a 100 V step (adjustable)
Sensitivity
5 mV
-
Voltage Monitor
Output
A buffered 0 to ±10 V output providing a representation of the measured voltage
Ratio
10:1 of the measured voltage or 20:1 of the measured voltage (switch selectable)
Output Current
5 mA
-
Front Panel Meter
Voltage Display
3.5-digit LED display
Range
Switch selectable for ±10 V or ±100 V full scale
Resolution
- 10 V Range: 0.01 V
- 100 V Range: 0.1 V
-
Mechanical
H x W x D
108 x 223 x 380 mm (4.25 x 8.75 x 15 in)
Weight
3.6 kg (8 lb)
-
Electrical
AC Line Cord Receptacle
Standard three-prong line cord with integral fuse holder
Line Supply
Factory set for one of two voltage ranges: 90 to 127 VAC or 180 to 250 VAC at 48 to 63 Hz (specify when ordering)
-
Typical Applications
- Materials evaluation
- Electret studies
- Charge accumulation on disk drive assemblies
-
EPA Regulation 40 C.F.R. 86.1312-2007
The Model 323 meets the requirements described for an electrostatic monitor under the Environmental Protection Agency (EPA); Title 40 Part 86 – Control of Emissions from New and In-Use Highway Vehicles and Engines. Specifically 40 C.F.R. 86.1312-2007 - Filter stabilization and microbalance workstation environmental conditions, microbalance specifications, and particulate matter filter handling and weighing procedures.
This EPA regulation for emission control describes the procedure for measuring particulates from vehicle emissions that are accumulated on a filter for weighing. During the weighing process static neutralizers such as Po-210 sources are used to neutralize any charge build up on the filter that could interfere with the filter weighing. To insure the Po-210 sources (or other static neutralizers) are operating properly a static monitor is used to measure residual charge on the filter before weighing. Static charge on the filter needs to be less than ±2V DC which requires the use of a static measuring device having sufficient low voltage resolution, low zero offset, and good sensitivity. The Model 323 with 0.01V of resolution and 5mV of sensitivity meets these requirements to insure accurate and repeatable measurements required by EPA regulation 40 C.F.R. 86.1312-2007.
Specifications are subject to change without notice. Not all options and accessories are available for all models and configurations. Dimensions listed generally refer to standard configurations and module bodies only. Please confirm technical specifications and customizations with a sales representative. Advanced Energy is not responsible for errors or omissions.
Data Sheets
Accessories
Documents & Support
View All Trek 323 AccessoriesGlobal Support & Services
Maximize fab productivity and capital equipment ROI with world-class support through each product lifecycle stage — from startup to long-term operation. Our service offerings are based on more than three decades of precision power and applications expertise.
Applications Support & Consulting
Accelerate tool installations and process development programs, or address specific applications concerns with Advanced Energy's dedicated applications consultants and engineering staff. Benefit from on-site reviews, analyses, and consultations.
Warranties
Decrease variability in maintenance costs and provide additional cost protection. Advanced Energy offers whole-box extended warranties.
Product Support
Call
U.S.: +1 800 446 9167
Asia: +86 29 8874 1895
China: 400 8899 130
EMEA: +44 800 032 1546
U.K.: 08000 321 546
Email
Thin Film Support
Thermal Product Support
Other Technical Support
Find an AE Representative or Distributor
To find distributors and representatives who sell AE products in your area, select your location and vendor type (optional).