High Voltage Products

Trek 603

Power Amplifier and Piezo Driver, Output Voltage Range 0 to +250 VDC or Peak AC

Advanced Energy’s Trek 603 is a high voltage DC power amplifier and piezo driver. It provides precise control of output voltages in bipolar or unipolar ranges that are customer-defined.

  • Output Voltage: 0 to +250 V DC or peak AC model dependent
  • Output Current: 0 to ±40 mA DC or ±80 mA peak AC for 1 ms
  • Slew Rate: Greater than 100 V/µs
  • Large Signal Bandwidth: DC to greater than 150 kHz (5% distortion)
  • Gain: 50 V/V or 25 V/V
  • Overview
  • Technical Specs
  • Documents
  • Accessories
  • Service & Support
  • Distributors

Overview

Select from Available Ranges and Options
The Trek 603 high-voltage amplifier/piezo driver offers precise control of output voltages in customer-specified bipolar or unipolar ranges.

Meet the Demands of Reactive Loads
The Trek 603 achieves accurate output responses and high slew rates by utilizing a four-quadrant active output stage that sinks or sources current into reactive or resistive loads. It’s configured as a non-inverting amplifier and is available in single or dual-channel packaging.

Benefits

  • Use on a benchtop or in a 19-in rack
  • Drive capacitive loads via a four-quadrant output
  • Enable high accuracy thanks to a closed-loop system
  • Safeguard equipment with short-circuit protection
  • Take advantage of low-output noise and ultra-accurate outputs

Features

  • Up to two independent amplifier channels in one enclosure
  • CE compliant for assured reliability
  • Reprogrammable factory-set output configurations
  • Dynamic Adjustment to optimize the AC response for various load parameters
  • Load range switch

Select specifications are shown below. Please see product data sheet for additional specifications.

  • Performance

    Output Voltage Range

    0 to ±125 V DC or peak AC
    0 to -250 V DC or peak AC
    0 to +250 V DC or peak AC

    Output Current Range

    ±40 mA DC
    ±80 mA peak AC, for less than 1 ms

    Gain

    50 V/V (a gain of 25 V/V is available)

    Slew Rate

    Greater than 100 V/μs (10% to 90%, typical)

    Large Signal Bandwidth

    DC to greater than 150 kHz (5% distortion)

  • Voltage Monitor

    Ratio

    1/25th of the high voltage output

    DC Accuracy

    Better than 0.1% of full scale

    DC Offset Voltage

    Less than 5 mV

    Output Noise

    Less than 5 mV rms
    (Measured using the true rms feature of the Hewlett Packard 34401A digital multimeter)

    Output Impedance

    0.1 Ω

  • Current Monitor

    Ratio

    0.1 V/mA

    DC Accuracy

    Greater than 1% of full scale

    Offset Voltage

    Less than 10 mV

    Output Noise

    Less than 10 mV rms
    (Measured using the true rms feature of the Hewlett Packard 34401A digital multimeter)

    Output Impedance

    0.1 Ω

  • Mechanical

    Dimensions

    Single Channel Instrument:
    222.3 x 108 x 381 mm (8.75 x 4.25 x 15 in)

    Double Channel Instrument:
    433.8 x 108 x 381 mm (17 x 4.25 x 15 in)

    Weight

    Single Channel Instrument:
    4.3 kg (9.4 lb)

    Double Channel Instrument:
    4.3 kg (9.4 lb)

  • Electrical

    Line Voltage

    Factory Set for one of two ranges:
    90 to 127 V AC or 180 to 250 V AC, either at 48 to 63 Hz

    Power Consumption

    125 VA, maximum

    AC Line Receptacle

    Standard 3-prong with integral fuse holder

  • Operating Conditions

    Temperature

    0 to 40°C (32 to 104°F)

    Relative Humidity

    To 85%, noncondensing

    Altitude

    To 2000 meters (6561.68 ft)

  • Typical Applications

    • Driving piezoelectric actuators
    • Modulating electrooptics
    • Electrostatically controlling ion beams
    • Providing remote ON/OFF capabilities for automated or computer controlled systems

Specifications are subject to change without notice. Not all options and accessories are available for all models and configurations. Dimensions listed generally refer to standard configurations and module bodies only. Please confirm technical specifications and customizations with a sales representative. Advanced Energy is not responsible for errors or omissions.

Accessories

Amplifier Selection Calculator

To help you select the appropriate Trek amplifier, we created this calculator. It uses peak-to-peak voltage to help calculate values associated with driving capacitive loads. If you have any difficulty with this software or would rather not do the download, please use the step-by-step calculator procedure.

Documents & Support

View All Trek 603 Accessories

Global Support & Services

Maximize fab productivity and capital equipment ROI with world-class support through each product lifecycle stage — from startup to long-term operation. Our service offerings are based on more than three decades of precision power and applications expertise.

Learn More

Applications Support & Consulting

Accelerate tool installations and process development programs, or address specific applications concerns with Advanced Energy's dedicated applications consultants and engineering staff. Benefit from on-site reviews, analyses, and consultations.

Learn More

Warranties

Decrease variability in maintenance costs and provide additional cost protection. Advanced Energy offers whole-box extended warranties.

Learn More

Product Support

Call
Inside the U.S.: 1.800.446.9167 (option 2)
Outside the U.S.


Email
Thin Film Support
Thermal Product Support
Other Technical Support

 

Find an AE Representative or Distributor

To find distributors and representatives who sell AE products in your area, select your location and vendor type (optional).

Contact Us

Thank You

You may now view any resource on the Advanced Energy site. Click the button below to view your requested resource.

Thank You

You may now view any resource on the Advanced Energy site. Click the button below to view your requested resource.