High Voltage Products

Trek 610E

High Voltage Amplifier, Controller, and Supply, Output Voltage 0 to ±1 kV or 0 to ±10 kV

Advanced Energy’s Trek 610E is a high voltage amplifier, controller, and supply that provides six modes of high voltage operation.

  • Output Voltage: 0 to ±1 kV or 0 to ±10 kV
  • Output Current: 0 to ±200 μA or 0 to ±2000 μA peak AC
  • Slew Rate: Greater than 35 V/µs
  • Large Signal Bandwidth: DC to greater than 1.2 kHz (-3dB)
  • Gain: 100 V/V (±1 kV) 1000 V/V (±10 kV)
  • Overview
  • Technical Specs
  • Documents
  • Accessories
  • Service & Support
  • Distributors

Overview

The Trek 610E offers six modes of high voltage operation.

Amplifier and Transconductance Amplifier
As a high voltage amplifier, the Trek 610E amplifies an externally applied signal with a switch-selectable setting of 100 V/V or 1000 V/V. When used a transconductance amplifier, an externally applied voltage signal produces a proportional output current.

Reference and Current Supply
As a high voltage reference supply, the Trek 610E’s front panel dial commands the output voltage, and, when used as a current supply, the same dial command the output currents.

Controller
The Trek 610E in controller mode maintains the high voltage amplifier mode but the amplifier input and feedback elements are uncommitted and available for user configuration.

Benefits

  • Benefit from enhanced utility via multi-mode operation
  • Configure as inverting, noninverting, or differential
  • Use in various applications, including closed-loop charge control, electrophotographic research, insulation testing, etc.
  • Drive capacitive loads via a four-quadrant output
  • Achieve high accuracy with a closed-loop system

Features

  • DC-stable for programmable supply applications
  • Low output noise for ultra-accurate outputs
  • NIST-traceable calibration certificate provided with each unit
  • Short-circuit protection for safeguarding equipment
  • CE compliant

Select specifications are shown below. Please see product data sheet for additional specifications.

  • Performance

    Output Voltage Range

    0 to ±1 kV or 0 to ±10 kV

    Output Current Range

    0 to ±200 µA or 0 to ±2000 µA peak AC

    Gain

    100 V/V (±1 kV) 1000 V/V (±10 kV)

    Slew Rate

    Greater than 35 V/µs

    Large Signal Bandwidth

    DC to greater than 1.2 kHz (-3dB)

  • Voltage Monitor

    Scale Factor

    1/1000th of the output voltage

    DC Scale Accuracy

    Better than 0.1% FS as referred to the high-voltage output

    DC Offset Voltage

    Less than 5 mV

  • Current Monitor

    Scale Factor

    1 V/200 µA

    DC Scale Accuracy

    Better than 0.1% FS as referred to the high-voltage output

    Offset Voltage

    Less than 10 mV

  • Mechanical

    H x W x D

    140 x 432 x 374 mm (5.5 x 17 x 15 in)

    Weight

    10.6 kg (23.5 lb.)

  • Electrical

    Line Voltage

    Factory set for one of four nominal voltages: 100 V, 120 V, 230 V at 48 to 63 Hz

    Power Consumption

    200 VA, maximum

    AC Line Receptacle

    Standard three-prong

  • Operating Conditions

    Temperature

    0 to 40°C (32 to 104°F)

    Relative Humidity

    To 85%, non-condensing

  • Typical Applications

    • Closed-loop charge control
    • Electrophotographic research
    • Insulation testing
    • Dielectric material evaluation
    • AC or DC calibrators and supplies

Specifications are subject to change without notice. Not all options and accessories are available for all models and configurations. Dimensions listed generally refer to standard configurations and module bodies only. Please confirm technical specifications and customizations with a sales representative. Advanced Energy is not responsible for errors or omissions.

Accessories

Amplifier Selection Calculator

To help you select the appropriate Trek amplifier, we created this calculator. It uses peak-to-peak voltage to help calculate values associated with driving capacitive loads. If you have any difficulty with this software or would rather not do the download, please use the step-by-step calculator procedure.

Documents & Support

View All Trek 610E Accessories

Global Support & Services

Maximize fab productivity and capital equipment ROI with world-class support through each product lifecycle stage — from startup to long-term operation. Our service offerings are based on more than three decades of precision power and applications expertise.

Learn More

Applications Support & Consulting

Accelerate tool installations and process development programs, or address specific applications concerns with Advanced Energy's dedicated applications consultants and engineering staff. Benefit from on-site reviews, analyses, and consultations.

Learn More

Warranties

Decrease variability in maintenance costs and provide additional cost protection. Advanced Energy offers whole-box extended warranties.

Learn More

Product Support

Call
Inside the U.S.: 1.800.446.9167 (option 2)
Outside the U.S.


Email
Thin Film Support
Thermal Product Support
Other Technical Support

 

Find an AE Representative or Distributor

To find distributors and representatives who sell AE products in your area, select your location and vendor type (optional).

Contact Us

Thank You

You may now view any resource on the Advanced Energy site. Click the button below to view your requested resource.

Thank You

You may now view any resource on the Advanced Energy site. Click the button below to view your requested resource.