- Products
- High Voltage Products
- High Voltage Amplifiers
- Standard & High Speed Amplifiers
- Trek 10/40A-HS
High Voltage Products
Trek 10/40A-HS
High-Speed, Non-Inverting High Voltage Amplifier, Output Voltage 0 to ±10 kV DC or Peak AC
Advanced Energy’s 10/40A-HS is a DC-stable, high-speed, high-voltage power amplifier used in industrial and research applications. Its all-solid-state design enables a high slew rate, vast bandwidth, and low-noise operation
- Output Voltage Range: 0 to ±10 kV DC or peak AC
- Output Current Range: 0 to ±40 mA DC or 120 mA peak AC for 1 ms (must not exceed 40 mA RMS max)
- Slew Rate: Greater than 900 V/µs
- Large Signal Bandwidth (-3 dB): DC to greater than 23 kHz, typical
- Gain: 1000 V/V
- Overview
- Technical Specs
- Documents
- Accessories
- Service & Support
- Distributors
Overview
The non-inverting Trek® 10/40A-HS is equipped with a four-quadrant, active output that sinks or sources the current into reactive or resistive loads throughout the output voltage range. This type of output is essential to achieve accurate output responses and high slew rates demanded by highly capacitive or reactive loads.
The Trek 10/40A-HS is optimal for electrophoresis, electro-optic modulation, material poling, and numerous other applications.
Benefits
- Drive capacitive loads via a four-quadrant output
- Enable high accuracy thanks to a closed-loop system
- Safeguard equipment with short-circuit protection
- Benefit from maintenance-free operation and solid-state design
- Take advantage of low-output noise and ultra-accurate outputs
Features
- NIST-traceable calibration certificate provided with each unit
- DC-stable for programmable supply applications
- Local and remote high voltage On/Off capabilities
- Switch selectable for current limit or trip
- CE compliant (230 VAC unit only)
Select specifications are shown below. Please see product data sheet for additional specifications.
-
Performance
Output Voltage Range
0 to ±10 kV DC or peak AC
Output Current Range
0 to ±40 mA DC or ±120 mA peak for 1 ms (must not exceed 40 mA rms, max)
Gain
1000 V/V
Slew Rate
Greater than 900 V/μs (10% to 90%, typical)
Large Signal Bandwidth
DC to greater than 23 kHz, typical
-
Voltage Monitor
Ratio
1/1000th of the high-voltage output signal
DC Accuracy
Better than 0.1% of full scale
DC Offset Voltage
Less than ±2 mV
Output Noise
Less than 10 mV rms
(Measured using the true rms feature of the HP Model 34401A digital multimeter)Output Impedance
47 Ω
-
Current Monitor
Ratio
1 V/12 mA
DC Accuracy
Better than 1% of full scale
Offset Voltage
Better than ±10 mV
Output Noise
Less than 30 mV rms
(Measured using the true rms feature of the HP Model 34401A digital multimeter)Bandwidth (-3dB)
DC to greater than 20 kHz
Output Impedance
47 Ω
-
Mechanical
Dimensions
279 x 482 654 mm (11 x 19 x 25.75 in)
Weight
24.9 kg (55 lb)
-
Electrical
Line Voltage
Factory Set for one of two ranges:104 to 127 VAC or 180 to 250 VAC, either at 48 to 63 Hz
Power Consumption
1000 VA, maximum
AC Line Receptacle
Standard IEC 320 three-prong AC line connector
-
Operating Conditions
Temperature
0 to 40°C (32 to 104°F)
Relative Humidity
To 85%, non-condensing
Altitude
To 2000 meters (6561.68 ft)
-
Typical Applications
- Electrostatic deflection
- Electrophoresis
- Electrorheological fluids
- Electro-optic modulation
- Material poling
- AC or DC biasing
- Ion beam steering
- Particle accelerators
- Mass spectrometers
- Material characterization
- Ferroelectrics
- Atmospheric plasma
- Dielectric barrier discharge
Specifications are subject to change without notice. Not all options and accessories are available for all models and configurations. Dimensions listed generally refer to standard configurations and module bodies only. Please confirm technical specifications and customizations with a sales representative. Advanced Energy is not responsible for errors or omissions.
Accessories
Documents & Support
View All Trek 10/40A-HS AccessoriesGlobal Support & Services
Maximize fab productivity and capital equipment ROI with world-class support through each product lifecycle stage — from startup to long-term operation. Our service offerings are based on more than three decades of precision power and applications expertise.
Applications Support & Consulting
Accelerate tool installations and process development programs, or address specific applications concerns with Advanced Energy's dedicated applications consultants and engineering staff. Benefit from on-site reviews, analyses, and consultations.
Warranties
Decrease variability in maintenance costs and provide additional cost protection. Advanced Energy offers whole-box extended warranties.
Product Support
Call
U.S.: +1 800 446 9167
Asia: +86 29 8874 1895
China: 400 8899 130
EMEA: +44 800 032 1546
U.K.: 08000 321 546
Email
Thin Film Support
Thermal Product Support
Other Technical Support
Find an AE Representative or Distributor
To find distributors and representatives who sell AE products in your area, select your location and vendor type (optional).