- Products
- High Voltage Products
- High Voltage Amplifiers
- Standard & High Speed Amplifiers
- Trek 10/10B-HS
High Voltage Products
Trek 10/10B-HS
High Speed, High Voltage Amplifier, Output Voltage 0 to ±10 kV DC or Peak AC
The Advanced Energy Trek 10/10B-HS is a DC-stable, high-speed, high-voltage power amplifier that showcases precise control of output voltages. It features an all-solid-state design, high slew rate, wide bandwidth, and low-noise operation.
- Output Voltage: 0 to ±10 kV DC or Peak AC
- Output Current: 0 to ±10 mA DC or 40 mA peak AC for 1 ms
- Slew Rate: Greater than 700 V/µs
- Large Signal Bandwidth: DC to greater than 19.5 kHz (-3dB)
- Gain: 1000 V/V fixed
- Overview
- Technical Specs
- Documents
- Accessories
- Service & Support
- Distributors
Overview
To enable accurate output responses and the high slew rates needed to drive reactive loads, the Trek® 10/10B-HS high voltage amplifier features a four-quadrant, active output. This output sinks or sources the current into reactive or resistive loads throughout the output voltage range.
The Trek 10/10B-HS is used in material poling, electrostatic deflection, AC or DC biasing, and various other applications.
Benefits
- Drive capacitive loads via a four-quadrant output
- Enable high accuracy thanks to a closed-loop system
- Safeguard equipment with short-circuit protection
- Benefit from maintenance-free operation and solid-state design
- Take advantage of low-output noise and ultra-accurate outputs
Features
- CE compliant
- DC-stable for programmable supply applications
- Dynamically adjust to optimize AC response for various load parameters
- Local and remote high voltage On/Off capabilities
- NIST-traceable calibration certificate provided with each unit
Select specifications are shown below. Please see product data sheet for additional specifications.
-
Performance
Output Voltage Range
0 to ±10 kV DC or peak AC
Output Current Range
0 to ±10 mA DC or ±40 mA peak for 1 ms
Gain
1000 V/V
Slew Rate
Greater than 700 V/μs (10% to 90%, typical)
Large Signal Bandwidth
DC to greater than 19.5 kHz
-
Voltage Monitor
Ratio
1 V/1000 V
DC Accuracy
Better than 0.1% of full scale
DC Offset Voltage
Less than ±3 mV
Output Noise
Less than 20 mV rms
(Measured using the true rms feature of the HP Model 34401A digital multimeter)Output Impedance
47 Ω
-
Current Monitor
Ratio
1 V/4 mA
DC Accuracy
Greater than 1% of full scale
Offset Voltage
Less than ±10 mV
Output Noise
Less than 50 mV rms
(Measured using the true rms feature of the HP Model 34401A digital multimeter)Bandwidth (-3dB)
DC to greater than 10 kHz
Output Impedance
47 Ω
-
Mechanical
Dimensions
190 x 432 x 417 mm (7.5 x 17 x 16.4 in)
Weight
14.9 kg (31 lb)
-
Electrical
Line Voltage
Factory Set for one of two ranges: 90 to 127 VAC or 180 to 250 VAC, either at 48 to 63 Hz
Power Consumption
680 VA, maximum
AC Line Receptacle
Standard 3-prong with integral fuse holder
-
Operating Conditions
Temperature
0 to 40°C (32 to 104°F)
Relative Humidity
To 85%, non-condensing
Altitude
To 2000 meters (6561.68 ft)
-
Typical Applications
- AC or DC biasing
- Atmospheric plasma
- Dielectric barrier discharge
- Electroactive polymers (EAP)
- Electrorheological fluids
- Electrostatic deflection
- Electro-optic modulation
- Ferroelectric material characterization
- Ion beam steering
- Mass spectrometers
- Material poling
- Particle accelerators
Specifications are subject to change without notice. Not all options and accessories are available for all models and configurations. Dimensions listed generally refer to standard configurations and module bodies only. Please confirm technical specifications and customizations with a sales representative. Advanced Energy is not responsible for errors or omissions.
Accessories
Documents & Support
View All Trek 10/10B-HS AccessoriesGlobal Support & Services
Maximize fab productivity and capital equipment ROI with world-class support through each product lifecycle stage — from startup to long-term operation. Our service offerings are based on more than three decades of precision power and applications expertise.
Applications Support & Consulting
Accelerate tool installations and process development programs, or address specific applications concerns with Advanced Energy's dedicated applications consultants and engineering staff. Benefit from on-site reviews, analyses, and consultations.
Warranties
Decrease variability in maintenance costs and provide additional cost protection. Advanced Energy offers whole-box extended warranties.
Product Support
Call
U.S.: +1 800 446 9167
Asia: +86 29 8874 1895
China: 400 8899 130
EMEA: +44 800 032 1546
U.K.: 08000 321 546
Email
Thin Film Support
Thermal Product Support
Other Technical Support
Find an AE Representative or Distributor
To find distributors and representatives who sell AE products in your area, select your location and vendor type (optional).