- Products
- High Voltage Products
- High Voltage Amplifiers
- Piezo Drivers
- Trek PZD2000A
High Voltage Products
Trek PZD2000A
High-Bandwidth, High Voltage Amplifier, Output Voltage 0 to ±2 kV DC or Peak A
Advanced Energy’s high-bandwidth Trek PZD2000A high voltage power amplifier is used for precision high power applications.
- Output Voltage Range: 0 to ±2 kV DC or Peak AC
- Output Current Range: 0 to ±200 mA DC or ±400 mA Peak AC
- Slew Rate: Greater than 750 V/µs
- Large Signal Bandwidth: DC to greater than 60 kHz (3% distortion):
- Gain: 200 V/V
- Overview
- Technical Specs
- Documents
- Accessories
- Service & Support
- Distributors
Overview
The Trek® PZD2000A high voltage power amplifier incorporates an all-solid-state design for high reliability and low-noise operation. Its four-quadrant output stage sinks and sources the load current throughout the output voltage range. This enables accurate output responses and high slew rates into highly capacitive loads. The output stage is fully protected against over-voltage and over-current conditions generated by active loads, overloads, or arcing to the ground.
Benefits
- Use remote high voltage on/off with automated or computer-controlled systems
- Adjust current limit or trip level
- Optimize the AC response for various load parameters
- Use in dielectric material characterization, polymer and ceramic corona poling, and piezoelectric driving and control applications
- Benefit from the all-solid-state design
Features
- DC accuracy is better than 0.1% of full-scale
- NIST-traceable calibration certificate provided with each unit
- Precision voltage and current monitors provide buffered low voltage representations of the high-voltage output and load current for monitoring purposes or use as feedback signals in closed-loop systems
- Output stage fully protected against over voltage and over current conditions generated by active loads, overloads, or arcing ground
Select specifications are shown below. Please see product data sheet for additional specifications.
-
Performance
Output Voltage Range
0 to ±2 kV DC or peak AC
Output Current Range
0 to ±200 mA DC or ±400 mA peak AC.
(Maximum duration for ±400 mA current pulse is 2 ms at 50% duty cycle using a square wave)Gain
200 V/V
Slew Rate
Greater than 750 V/μs (10% to 90%, typical)
Large Signal Bandwidth
DC to greater than 60 kHz (3% distortion)
-
Voltage Monitor
Ratio
1/200th of the high voltage output
DC Accuracy
Better than 0.1% of full scale
DC Offset Voltage
Less than ±2 mV
Output Noise
Less than 5 mV rms
(Measured using the true rms feature of the Hewlett Packard Model 34401A digital multimeter)Output Impedance
47 Ω
-
Current Monitor
Ratio
0.025 V/mA
DC Accuracy
Greater than 1% of full scale
Offset Voltage
Less than ±10 mV
Output Noise
Less than 10 mV rms
(Measured using the true rms feature of the Hewlett Packard Model 34401A digital multimeter)Bandwidth (-3dB)
DC to greater than 5 kHz
Output Impedance
47 Ω
-
Mechanical
Dimensions
266 x 482 x 655 mm (10.5 x 19 x 25.8 in)
Weight
24.9 kg (55 lb)
-
Electrical
Line Voltage
Factory set for one of two ranges:
104 to 126 V AC or 180 to 250 V AC, at 48 to 63 HzPower Consumption
1000 VA, maximum
AC Line Receptacle
Standard three-prong AC line connector
-
Operating Conditions
Temperature
0 to 40°C (32 to 104°F)
Relative Humidity
To 75%, non-condensing
Altitude
To 2000 meters (6561.68 ft)
-
Typical Applications
- Dielectric material characterization
- Polymer and ceramic corona poling
- Piezoelectric driving and control
Specifications are subject to change without notice. Not all options and accessories are available for all models and configurations. Dimensions listed generally refer to standard configurations and module bodies only. Please confirm technical specifications and customizations with a sales representative. Advanced Energy is not responsible for errors or omissions.
Accessories
Documents & Support
View All Trek PZD2000A AccessoriesGlobal Support & Services
Maximize fab productivity and capital equipment ROI with world-class support through each product lifecycle stage — from startup to long-term operation. Our service offerings are based on more than three decades of precision power and applications expertise.
Applications Support & Consulting
Accelerate tool installations and process development programs, or address specific applications concerns with Advanced Energy's dedicated applications consultants and engineering staff. Benefit from on-site reviews, analyses, and consultations.
Warranties
Decrease variability in maintenance costs and provide additional cost protection. Advanced Energy offers whole-box extended warranties.
Product Support
Call
U.S.: +1 800 446 9167
Asia: +86 29 8874 1895
China: 400 8899 130
EMEA: +44 800 032 1546
U.K.: 08000 321 546
Email
Thin Film Support
Thermal Product Support
Other Technical Support
Find an AE Representative or Distributor
To find distributors and representatives who sell AE products in your area, select your location and vendor type (optional).