Temperature Measurement Products

Impac ISR 6-TI Advanced

Stationary, Digital Hybrid Pyrometer with Built-In Thermal Imaging Camera, 700 to 1800°C

Advanced Energy’s Impac ISR 6-TI Advanced pyrometer combines the two-color method and thermal imaging in a single non-contact temperature measurement system.

  • Built-in video camera with short wavelength infrared filter
  • Thermal image auto-calibration
  • Fast response times (2 ms)
  • Dirty-window warning
  • Robust, stainless steel sensor
  • Overview
  • Technical Specs
  • Documents
  • Accessories
  • Service & Support

Overview

The Impac® ISR 6-TI is a pyrometer and thermal imager. It uses two-color (ratio) technology to measure the center spot’s temperature. The built-in video camera’s infrared filter auto-calibrates a thermal image. The video output is transferred to your PC via USB and InfraWin software generates the image.

You can define and evaluate specific regions of interest (ROIs) within the thermal image. Use an optional I/O module to trigger external switching contacts based on one or several ROIs.

Benefits

  • Define and evaluate ROIs
  • Use in harsh environments
  • Achieve high accuracy with two-color (ratio) pyrometer technology
  • Easily measure fast processes
  • Utilize optional I/O module to trigger external switching contacts

Features

  • Pyrometer and thermal imager
  • Built-in video camera with short wavelength infrared filter
  • Thermal image auto-calibration relative to temperature reading
  • Video cable and video-to-USB grabber for use with InfraWin software
  • Fast response times (2 ms)
  • Dirty-window warning
  • Robust, stainless steel sensor

Select specifications are shown below. Please see product data sheet for additional specifications.

  • Temperature Range

    ISR 6-TI Advanced

    700 to 1800°C (1292 to 3272°F) (MB 18)
    Any range adjustable within the temperature range, minimum span: 50°C

  • Measurement

    Spectral Ranges

    Channel 1: 0.9 μm
    Channel 2: 1.05 μm

    Measurement Uncertainty

    < 1500°C: 0.3% of reading in °C + 2°C
    > 1500°C: 0.6% of reading in °C
    At κ = 1 or ε = 1, t90 = 1 s, Tamb. = 25°C

    Repeatability

    0.15% of reading in °C + 1°C
    At κ = 1 or ε = 1, t90 = 1 s, Tamb. = 25°C

    Exposure Time t90:

    <2 ms (with dynamic adaption at low signal levels); adjustable to min, 0.01 s, 0.05 s, 0.25 s, 1 s, 3 s, 10 s

    Emissivity ε

    0.050 to 1.000 in steps of 1/1000 (one-color mode)

    Transmittance τ

    0.050 to 1.000 in steps of 1/1000 (one-color mode)

  • Optical

    Sighting

    Thermal image with marked pyrometer spot

    Optics

    Manually focusable from rear cover measuring distance a = 210 to 5000 mm

    Distance Ratio

    Approximately 190:1

  • Interface and Communication

    Connection

    12-pin connector

    Connection Video Signal

    Separate triaxial contact at pyrometer for double screened signal transmission
    Connection cable with BNC-connector on user’s side

    Display

    In Rear Cover: LED, four-digit matrix, 5 mm high for two-color or one-color temperature signal or measuring distance

    Parameters

    Analog Output

    Adjustable 0 to 20 mA or 4 to 20 mA, linear (via digital interface)

    Digital Interface

    RS485 addressable (half-duplex)
    Baud Rate: 1200 to 115.2 kBd
    On request RS232, not addressable

    Video Signal

    FBAS-Signal approximately 1 VSS on 75 Ohm, PAL (B), 50 Hz, CCIR656

    Dirty-Window Warning

    Relay contact, maximum continuous current 0.4 A, setting of the warning level: 0 (off) to 99%

  • Environmental

    Protection Class

    IP 65 IEC 60529 (value in mated condition)

    Operating Position

    Any

    Ambient Temperature

    0 to 60°C (0 to 140°F) at housing

    Storage Temperature

    -20 to 80°C (-4 to 176°F)

    Relative Humidity

    Non-condensing conditions

    Weight

    0.755 kg (~1.66 lbs)

    Housing

    Stainless steel

    CE Label

    According to EU directives about electromagnetical immunity

  • Electrical

    Power Supply

    24 VDC ±25%, ripple must be less than 50 mV
    If instrument is used in combination with an I/O module, a power supply with minimum 1 A is required

    Power Consumption

    Approximately 8.5 W

    Load

    0 to 500 Ω

    Isolation

    Power supply, analog output, digital interface, and video signal are electrically isolated from each other

  • Thermal Imaging Feature

    Relative Temperature Span

    In one image (depends on temperature): 100 to 200°C distributed around the spot temperature (for one dynamic range), possible combination of multiple ranges can be used so complete temperature range of pyrometer can be displayed

    Pixels

    768 x 576

    Frequency

    Up to 25 Hz

    Signal

    Analog video (PAL), USB (video grabber)

    Field of View

    6.0° x 4.5° (e.g. 105 x 78 mm at 1000 mm distance)

    Calibration of Thermal Image

    Relative to central pyrometer spot

  • Typical Applications

    • Metal Industry: melting processes, melting furnaces, vacuum furnaces, coating processes, welding processes, induction heating processes, sintering processes
    • Glass Industry: glass gob
    • Semiconductor Industry: sapphire growth
    • Other Industries: e.g. waste combustion

Specifications are subject to change without notice. Not all options and accessories are available for all models and configurations. Dimensions listed generally refer to standard configurations and module bodies only. Please confirm technical specifications and customizations with a sales representative. Advanced Energy is not responsible for errors or omissions.

Global Support & Services

Maximize fab productivity and capital equipment ROI with world-class support through each product lifecycle stage — from startup to long-term operation. Our service offerings are based on more than three decades of precision power and applications expertise.

Learn More

Applications Support & Consulting

Accelerate tool installations and process development programs, or address specific applications concerns with Advanced Energy's dedicated applications consultants and engineering staff. Benefit from on-site reviews, analyses, and consultations.

Learn More

Warranties

Decrease variability in maintenance costs and provide additional cost protection. Advanced Energy offers whole-box extended warranties.

Learn More

Product Support

Call
Inside the U.S.: 1.800.446.9167 (option 2)
Outside the U.S.


Email
Thin Film Support
Thermal Product Support
Other Technical Support

Thank You

You may now view any resource on the Advanced Energy site. Click the button below to view your requested resource.

Thank You

You may now view any resource on the Advanced Energy site. Click the button below to view your requested resource.