High Voltage Products
Trek 609E-6
High Voltage Amplifier for Industrial and Research Applications, Output Voltage 0 to ±4 kV DC or Peak AC
Advanced Energy's Trek 609E-6 high voltage amplifier features a four-quadrant output and low-noise operation.
- Output Voltage: 0 to ±4 kV DC or Peak AC
- Output Current: 0 to ±20 mA DC or Peak AC
- Slew Rate: Greater than 150 V/μs
- Large Signal Bandwidth: DC to greater than 13 kHz (-3 dB)
- Gain: See datasheet
- Overview
- Technical Specs
- Documents
- Accessories
- Service & Support
- Distributors
Overview
The DC-stable Trek® 609E-6 high-voltage amplifier is used for electrostatic chucks, mass spectrometers, and various other industrial and research applications. Its low-noise operation, extensive bandwidth, and high slew rates are backed by an all-solid-state design. And you can wire different input configurations into the unit. Configure as non-inverting, inverting, or differential.
Built for Demanding High Capacitive and Reactive Loads
The Trek 609E-6’s four-quadrant, active output stage sinks or sources the current into reactive or resistive loads throughout the output voltage range. This is essential for the accurate output responses and high slew rates demanded by a variety of loads.
Benefits
- Drive capacitive loads via a four-quadrant output
- Enable high accuracy thanks to a closed-loop system
- Safeguard equipment with short-circuit protection
- Take advantage of low-output noise and ultra-accurate outputs
Features
- Dynamic adjustment optimizes the AC response for various load parameters
- NIST-traceable calibration certificate provided with each unit
- DC-stable for programmable supply applications
- Local and remote high voltage On/Off capabilities
- Switch selectable for current limit or trip
Select specifications are shown below. Please see product data sheet for additional specifications.
-
Performance
Output Voltage Range
0 to ±4 kV DC or peak AC
Output Current Range
0 to ±20 mA DC or peak AC
Gain
1000 V/V
Slew Rate
Greater than 150 V/μs (10% to 90%, typical)
Large Signal Bandwidth
DC to greater 6 kHz (1% Distortion)
DC to greater 13 kHz (-3 dB) -
Voltage Monitor
Ratio
1/1000th of the high-voltage output signal
DC Accuracy
Better than 0.1% of full scale
DC Offset Voltage
Less than ±2.5 mV
Output Noise
Less than 2 mV rms
(Measured using the true rms feature of the HP Model 34401A digital multimeter)Output Impedance
47 Ω
-
Current Monitor
Ratio
0.5 V/mA
DC Accuracy
Better than 0.5% of full scale
Offset Voltage
Less than ±5 mV
Output Noise
Less than 10 mV
(Measured using the true rms feature of the HP Model 34401A digital multimeter)Output Impedance
47 Ω
-
Mechanical
Dimensions
140 x 432 x 439 mm (5.5 x 17 x 17.25 in)
Weight
13.2 kg (29 lb)
-
Electrical
Line Voltage
Factory Set for one of two ranges:
90 to 127 VAC or 180 to 250 VAC, either at 48 to 63 HzPower Consumption
220 VA, maximum
-
Operating Conditions
Temperature
0 to 40°C (32 to 104°F)
Relative Humidity
To 85%, non-condensing
Altitude
To 2000 meters (6561.68 ft)
-
Typical Applications
- AC or DC biasing
- Atmospheric plasma
- Dielectric barrier discharge
- Electroactive polymers (EAP)
- Electrophoresis, electrophotography
- Electrorheological fluids
- Electrostatic deflection
- Electro-optic modulation
- Ferroelectric material characterization
- Ion beam steering
- Mass spectrometers
- Material poling and particle accelerators
Specifications are subject to change without notice. Not all options and accessories are available for all models and configurations. Dimensions listed generally refer to standard configurations and module bodies only. Please confirm technical specifications and customizations with a sales representative. Advanced Energy is not responsible for errors or omissions.
Accessories
Documents & Support
View All Trek 609E-6 AccessoriesGlobal Support & Services
Maximize fab productivity and capital equipment ROI with world-class support through each product lifecycle stage — from startup to long-term operation. Our service offerings are based on more than three decades of precision power and applications expertise.
Applications Support & Consulting
Accelerate tool installations and process development programs, or address specific applications concerns with Advanced Energy's dedicated applications consultants and engineering staff. Benefit from on-site reviews, analyses, and consultations.
Warranties
Decrease variability in maintenance costs and provide additional cost protection. Advanced Energy offers whole-box extended warranties.
Product Support
Call
U.S.: +1 800 446 9167
Asia: +86 29 8874 1895
China: 400 8899 130
EMEA: +44 800 032 1546
U.K.: 08000 321 546
Email
Thin Film Support
Thermal Product Support
Other Technical Support
Find an AE Representative or Distributor
To find distributors and representatives who sell AE products in your area, select your location and vendor type (optional).