Gas Sensors

Innova 1512

Highly Accurate, Stable, Quantitative, and Remotely Controllable Gas Monitoring System

Advanced Energy's Innova 1512 is based on the photoacoustic infrared spectroscopy and delivers superior sensitivity in a very compact form factor. Extremely versatile by design, the 1512 is capable of measuring almost any gas that absorbs infrared light.

  • Leverages the unique strengths of the photoacoustic sensor technique
  • User-friendly, stable, reliable, and highly accurate
  • Extremely low-volume flushing possible
  • Overview
  • Technical Specs
  • Documents
  • Accessories
  • Service & Support

Overview

Advanced Energy’s Innova® 1512 is a highly accurate, reliable, and stable quantitative gas monitoring system. Its measurement system, based on the photoacoustic infrared detection method, is capable of measuring almost any gas that absorbs infrared light.

Gas selectivity is achieved through the use of optical filters. By installing up to five filters, the 1512 can measure the concentration of up to five component gases and water vapor in any air sample. The detection limit is gas-dependent, but is typically in the ppb region. Accuracy of these measurements is ensured by the 1512’s ability to compensate for temperature and pressure fluctuations, water vapor interference, and interference from other gases known to be present.

Benefits

  • Selectively measure a wide range of gases / vapors
  • Ensure a maximum of only two calibrations a year
  • Operate immediately with virtually no warm-up time necessary
  • Easily calibrate, configure, and view / analyze data via PC
  • Accurately compensate for temperature and pressure fluctuations, water vapor interference, and interference from other known gases

Features

  • Linear response over a wide dynamic range
  • Remote control capability via TCP/IP network interface protocol
  • Expandable up to 24 locations with Innova 1409 Multipoint Sampler; the gas monitor can operate as the system controller for full standalone operation
  • Includes BZ7002 calibration software
  • Includes BZ7003 offline software to set up the gas monitor without connecting it to a PC and to download data stored in the gas monitor's internal memories
  • Measurement Specifications

    Detection Limit

    Gas dependent, but typically in the ppb region; using the Gas Detection Limits Chart, the detection limit for a selected sample integration time (SIT) can be calculated

    Dynamic Range

    Typically four orders of magnitude (i.e., 10,000 times the detection limit at 5 SIT); using two span concentrations it can be expanded to five orders of magnitude

    Repeatability

    1% of measured value
    Measured at 20°C, 1013 mbar, and relative humidity (RH): 60%; a concentration of 100x detection limit (5s SIT) was used in determining these specifications

    Interference

    The 1512 automatically compensates for temperature and pressure fluctuations in its analysis cell and can compensate for water vapor in the air sample; if an optical filter is installed to measure a known interferent, the 1512 can cross compensate for the interferent

    Internal Data Storage Capacity

    The total space available in display memory to store data ia 131072 measurement cycles; if a measurement cycle takes 15 sec, then the display Memory space will be sufficient for a 22-day monitoring task

  • Environmental Specifications

    Operating Temperature

    5 to 40°C (41 to 104°F)

    Humidity

    Maximum relative humidity: 80% for temperatures up to 31°C, decreasing linearly to 50% relative humidity at 40°C

    Enclosure

    IP 20

    H x W x D

    195 x 443 x 244 mm (7.68 x 17.44 x 9.60 in)

    Weight

    11 kg (24.3 lb)

  • Pumping System Specifications

    Pumping Rate

    30 cm3/s (flushing sampling tube) and 5 cm3/s (flushing measurement chamber)

    Air Volume Per Sample

    Total Internal Volume

    60 cm3 (of the measurement system)

  • Electrical and Communication Specifications

    Power Ratings

    ~85 VA, 100 to 240 VAC ±10%, 50 to 60 Hz, Class 1

    Alarm Relay Socket

    For connection to one or two alarm relays (visual / audio)
    Alarm levels for each gas are user-defined
    System on / running status available
    Maximum 25 VDC, maximum 100 mA

    Back-Up Battery

    3 V lithium battery, lifetime 5 years; this protects data stored in memory and powers the internal clock

    Monitor Interface

    Three interfaces: USB, Ethernet, and RS232, for data exchange and remote control of the instrument

    Software Communication

    Via USB, Ethernet, or RS232 interface

  • Safety and Standards Specifications

    Safety

    EN/IEC 61010-1 3rd edition
    CAN/CSA C22.2 No. 61010-1-04
    UL 61010-1 3rd edition

    EMC

    EN 61326-1:2013: Electrical equipment for measurement, control and laboratory use – EMC requirements; Part 1: General requirements

    Standards Compliance

    CE-mark indicates compliance with: EMC Directive and Low Voltage Directive
    NEMKO mark indicates compliance with: CSA and UL Standards

  • Typical Applications

    • Measurement of refrigerant emissions from mobile A/C systems
    • Animal husbandry
    • Soil science
    • Fumigant monitoring
    • Contaminated soil
    • Ventilation performance
    • Industrial hygiene-IAQ monitoring
    • Waste anesthesia monitoring
    • Biogas analysis
    • Sorbent gas filter testing
    • Photocatalytic material testing
    • Research and development
    • SF6 leak testing

Specifications are subject to change without notice. Not all options and accessories are available for all models and configurations. Dimensions listed generally refer to standard configurations and module bodies only. Please confirm technical specifications and customizations with a sales representative. Advanced Energy is not responsible for errors or omissions.

Accessories

LumaSoft Multipoint 7880

Application Software to perform Gas Monitoring tasks in up to 24 locations

Innova 7650 Basic

Application Software for Ventilation and Air-Exchange Measurements

Global Support & Services

Maximize fab productivity and capital equipment ROI with world-class support through each product lifecycle stage — from startup to long-term operation. Our service offerings are based on more than three decades of precision power and applications expertise.

Learn More

Applications Support & Consulting

Accelerate tool installations and process development programs, or address specific applications concerns with Advanced Energy's dedicated applications consultants and engineering staff. Benefit from on-site reviews, analyses, and consultations.

Learn More

Warranties

Decrease variability in maintenance costs and provide additional cost protection. Advanced Energy offers whole-box extended warranties.

Learn More

Product Support

Call
Inside the U.S.: 1.800.446.9167 (option 2)
Outside the U.S.


Email
Thin Film Support
Thermal Product Support
Other Technical Support

Thank You

You may now view any resource on the Advanced Energy site. Click the button below to view your requested resource.

Thank You

You may now view any resource on the Advanced Energy site. Click the button below to view your requested resource.